DT SWISS H 1900 SPLINE 30 HYBRID FRONT WHEEL

Product Code: 153701
£154.99GBP
Loading

Colour

  • Black

Size

  • 27.5"
Adding to basket
  • Colour:---
  • Size:---
Product Description

H 1900 Hybrid wheel, 30 mm rim, 15 x 110 mm BOOST axle

With its hybrid wheel sets, DT-Swiss is launching its first series of impellers, specially developed for use with eMTBs. Not only the system weight at eMTBs is higher and leads to higher loads for the wheels, also many trails and rough passages can be driven at significantly higher speeds. In addition to this, the drive system generates higher driving torques which are required to be placed on the ground and require stiffer wheels. The engineers at DT-Swiss have taken this requirement into account and optimized all components of their proven Spline wheel sets for use with eMTBs.

The H 1700 Spline wheels with a 30- or 35-millimeter gap provide a good support for tires up to 3.5 inches, even at low air pressures. With a clearance of up to 150 kilos of system weight (driver, clothing, wheel), the H 1700 wheels also provide enough reserves for rough riders on rough trails.

Read more
* Prices are estimates and will be calculated at checkout based on your minimum deposit.
Home Delivery by Experts

All Terrain Cycles are now offering a Home Delivery service.

Our Cytech qualified mechanics will first make sure that your bike is fully checked and ready to ride.

Then we will deliver it completely assembled direct to your home or place of work where we will set up your bike for your personal needs and answer any questions you may have. All for just £50.00.

Our delivery map indicates a general area, however, if you do not see your location on the map please call us on 01274 588488 to discuss a special delivery.

Hometech Map
HOW TO BUILD YOUR MAIL ORDER BIKE

Aftercare

After the first few weeks of use, the whole bike will settle down. As a result, the gears may need tweaking, some nuts and bolts may need tightening and you may well need to check the adjustment of the saddle and handlebars.

CABLE STRETCH

Gears

Cable stretch tends to occur shortly after a new bike has been ridden a few times. A rear derailleur that we have tuned to hit every gear, nicely and quietly, may now not be making each shift causing a sensation and sound of “being in between gears”. Generally you may have to shift up, or shift down a couple times to quiet it down and settle the derailleur into a “happy gear”. A front derailleur may no longer want to shift all the way onto the big ring or will require a much firmer push to get it there.

It is advisable to get the cable tension adjusted as soon as this happens either by your local bike shop. This tune up is considered a necessary part of any bicycles maintenance schedule and as such should not be ignored.
Brakes

Your brakes will also be affected by cable stretch (provided of course that they are NOT hydraulic in which case this does not apply). The symptom here is that they usually start to feel quite loose. i.e. you have to pull the lever much further back or harder in order to get the same stopping power you once had. This is partly why new bikes come with a first free service. If your brakes start feeling a little spongy after a few weeks, you can adjust them at the barrel or the clamp or ask a mechanic at your local bike shop to do it for you.
DISC BRAKES

New disc brakes won’t deliver their full power until the rotor and pads have bedded in.

SRAM has a really good guide for bedding in disc brakes:

“Accelerate the bike to a moderate speed and then firmly applying the brakes until you are at walking speed. Repeat this process 20 times. Then accelerate the bike to a faster speed and apply the brakes until you are at walking speed. Repeat this process ten times. It’s important that during this process you never come to a complete stop or lock up the wheels at any point.”

Doing this process should drastically improve the performance of your brakes and prepare them for many happy rides.
CRANKS

Check the cranks and crank bolts or nut for tightness; grab a crank arm in each hand and try to wiggle them to check for looseness. If there is play in the cranks, the nuts or bolts may need to be tightened. Cranks should be checked after every ride for the first week.
HEADSET

A loose headset can be diagnosed by turning the front wheel to point left or right, holding the front brake on, and then rocking the bike backwards and forwards. Hold your fingers between the stem and the frame. Any movement indicates that you need to tighten the headset.
SADDLE

Check your seat post is not loose and that you have not exceeded the limit marked on the seat post. Once you have checked these, use an allen key to tighten the seat post clamp. Check the seat is secure by giving it another check once you have finished.
STEM

Check that your front wheel and stem do not move independently, and that your handlebar clamp bolts are tight. Perform this check by standing in front of the bike, holding the front wheel between your knees, and twisting the handlebars. You can prevent any movement by tightening the stem bolts and the handlebar clamp with an allen key.
SUSPENSION FORKS

Keeping your mountain bike’s suspension maintained is one of the best ways to ensure you’re getting all the performance you can out of your bike. Plus, giving your fork and shock a few seconds of attention here and there can prevent costly repairs or even replacements.

Dirt is the number one enemy of suspension. After every ride make sure to wipe the seal area and stanchions of your fork and shock. Wipe in a horizontal motion, not vertical as you don’t want to force any debris towards the seals.

Every few rides double check that your suspension sag is correct, as well as your rebound and compression adjustments. If something has changed, or the adjustments aren’t working as before, some maintenance is likely due.

Working on your bike at home can seem daunting, and we'd always recommend you take your bike to a qualified mechanic if possible.

FOR FURTHER ADVICE ON LOOKING AFTER YOUR NEW BIKE SEE OUR KNOWLEDGE CENTRE.

knowledgecentre

Mail Order

One of our Cytech qualified mechanics will hand build your bike leaving only a few minor adjustments for you to do once your new bike arrives. Our mechanic will also complete a rigorous Pre-Delivery Inspection (PDI) before carefully re-packing for shipping to you; but in order to fit the bike back into its box for delivery, some disassembly has to be done. Re-assembly of these parts should be straightforward and should not take very long.

Tools You'll Need (Not Provided)

A multi-tool or a 4mm or 5mm Allen key, a pedal wrench or 15mm Allen key, depending on your pedals and a pair of scissors to open the box and cut the zip-ties with.
1. Open the Box and Remove Your Bike

Carefully remove your bike from the box and remove all of the packaging and zip ties with your scissors or snips. Never use a sharp knife as this can easily result in damage to paintwork and tyre sidewalls. Pedals and quick release (if supplied) will be in a small box at the bottom of your package as well as an instruction manual for your specific bike. Make sure you keep hold of this as it contains your bike's serial number.
2. Secure Your Front Wheel

Bikes will be delivered with the rear wheel already fitted so all you have to do is slide in the front wheel. First, remove the plastic fork spacer, along with any other packing material.

Set the frame upright on the ground and attach the wheel. Make sure that the brake is properly aligned and that the wheel is sitting straight. Next, tighten the quick release skewer if supplied and make sure that the brake quick release is tightened.
3. Attach the Handlebars

Using a multi-tool or a 4 or 5mm Allen key, clamp the faceplate over the bars so that they are fastened securely but not so tight that you cannot change the angle of the bars. Note many models of handlebar have handy measurement markers, allowing you to find your perfect angle.
4. Fit Your Pedals

It is important to note that pedal threads are different from left side and right side. The right side pedal has a right-hand thread (removes anti-clockwise, installs clockwise). The left side pedal has a left-hand thread (removes clockwise, installs anti-clockwise). We will label the pedals with “left and right” stickers in order to make sure you refit them correctly. The pedals will have grease applied to the threads, do not wipe this off. Follow the direction arrows on the stickers to ensure the pedal threads engage correctly then tighten them with a 15mm pedal wrench or Allen key (where applicable).
5. Fit Your Saddle

The seatpost has already been greased so all you have to do is slide the post into the frame at your desired height and tighten the seat clamp using your multi-tool.
6. Final Checks

Finally give your bike a final check over to ensure your handlebars and seat post clamp are tightened securely, and also that your brakes' quick releases are in the closed position.

Please also read our aftercare recommendations.

FOR FURTHER ADVICE ON LOOKING AFTER YOUR NEW BIKE SEE OUR KNOWLEDGE CENTRE.

knowledgecentre

Questions and Answers

There are currently no questions and answers for this product.

Want to ask us a question about this product? Just fill in the form below and we will get back to you as soon as we can.

Customer Reviews

There are currently no reviews for this product.

  • 0/5 Stars

(Be the first to review)
Recently bought this item? Leaving a review can be helpful to us and to other customers. If you would like to leave a review please fill in the form below.
  • 5/5 Stars
Availability

Stock is held at our two stores and at an external warehouse, and as a consequence our website does not show live stock.

Upon placing an online order we will notify you if we are unable to fulfil your order within 1-5 working days.

We do not charge your credit or debit card until we dispatch your order, unless by prior agreement or as a holding deposit for special purchase items.

Our mail Order Customer service is open Monday to Friday 8am to 5.30pm

If you are visiting one of our stores and interested in a specific item, please ring us on 01274 588 488 to check that it is available at the store you are visiting before making a special trip.

This telephone number is manned 7 days a week in line with our shop opening hours.

Returns

Goods must be returned within 30 days of receipt.

Returned goods must be unused, in a saleable condition and in their original packaging with all labels still attached.

Goods must not be fitted or used.

All Goods must be accompanied with a Completed Returns Form.

Goods can be returned to the Store for a refund or exchange. A Completed Returns form must accompany all goods returned to the store; the refund however will be processed by the Mail Order Customer Service Staff and not by the Store Staff so the refund may not be immediate.

To read more about our delivery/returns please click here

Specifications
Hybrid front hub

The hybrid hub has an oversized housing, a heavy duty axle and extra reinforced spoke mountings. Over-dimensioned bearings additionally ensure high robustness and durability. Despite these adjustments, the hybrid hub adds a very small extra weight compared to a standard MTB hub. The spline hub flanges for Straigthpull spokes also make the hub optically an eyecatcher.

Hybrid spokes

In order to transfer the higher drive forces to the rims, DT-Swiss developed special oversized hybrid spokes. They consist of the same high-performance steel alloy as all the tried and tested DT Swiss spokes. However, the Straightpull hybrid spokes are equipped with reinforced and oversized fuel heads, which together with the DT Pro Lock Squorx nipples ensure that every watt on the rim arrives.

Hybrid wheels

Due to the system's increased overall weight, the rims of e-bikes must be able to push away more than on conventional MTBs. At first glance, the hybrid rims differ from the standard DT Swiss enduro rims. So they have the same Tubelessready rim profile with load-optimized cross-sections. However, in the case of the hybrid rims, material strength and strength were increased at the critical points in order to maintain the higher loads permanently.

Technical specifications:
  • Intended use : E-Bike, Tour, All Mountain, Trail
  • Wheel size: 27.5 "(ETRTO: 584 x 30 | 35 mm)
  • Type of rim: clincher (wire and folding)
  • Brake type: only for disc brake
  • Brake disc mount: 6-hole (IS2000)
  • Material: aluminum, steel
  • Internal width: 30 or 35 mm
  • External width: 35 or 40 mm
  • Wheel height: 20 mm
  • Number of holes: 28 holes
  • Axle type : 15x110 mm Plug-in axle (BOOST / Outboard)
  • Bearing : 2x oversized industrial storage
  • Seal: labyrinth rubber seals
  • Spokes: 28x DT Swiss hybrid spokes, straightpull
  • Tubeless capable: yes
  • Recommended tire width: 1.85 "-3.5" (47-89 mm)
  • Maximum driver weight: 150 Kg (driver, bike, clothing and possibly luggage)
  • Colour: black, white hub body, white logos
Weights (manufacturer's data):
  • 959g (30mm rim)
  • 1014g (35mm rim)
You might be interested in